火**售日本進口SMC小型壓力開關
上海乾拓貿(mào)易有限公司
電話：
手機： (微信)
郵箱：@163.com
企業(yè)QQ：
聯(lián)系人：
地址：室
 whichever is smaller of 1.5 mm amplitude or 98 m/s2 acceleration, in X, Y, Z directions for 2 hrs. each (De-energized)
Air/Non-corrosive, non-flammable gas 1.5 MPa500 kPa
1000 VAC for 1 min. (between live parts and case) 50 MΩ or more (at 500 VDC by megameter) between live parts and case
35 g (Including 0.6 m-Long lead wire) Oil-resistant vinyl cabtire code 3 cores, ?3.4,
 Cross section: 0.2 mm2, Insulator O.D.: 1.1 mm Heat-resistant vinyl electric wire, 3-wire,
ISE2 For positive pressure 0 to 1 MPa
12 to 24 VDC ±10%, Ripple (P-P) 10% or less (With power supply polarity protection) 17 mA or less at 24 VDC 5 ms
? Regarding the pressure setting
Observe the following precautions for setting the vacuum pressure: Use your fingertips to gently turn the screwdriver.
 Do not use a screwdriver with a large grip or with a tip that does not fit into the trimmer groove because this could strip the groove.
Hysteresis is the pressure difference between  the ON and the OFF pressure of the output signal.
Enclosure Operating temperature range Operating humidity range Vibration resistance Impact resistance
Lever DC polarity indicator Connector Socket
Lead wireSocket Covering retainerCore wire crimping area
2. Crimping of lead wires and sockets Strip 3.2 to 3.7 mm at the end of the lead wires, insert the ends of core wires evenly into the sockets,
or less ±1% F.S. or less IP40 Operating: 0 to 60°C, Stored: –10 to 60°C
0R: Base mount type (For mounting on ZR unit)
–15 –55 NPN open collector 30V, 80 mA or less PNP open collector 80 mA or less 1 V or less
 (With load current of 80 mA) 1 3% F.S. or less (Fixed) ON: when output is ON (Red) 200°
Switch output Residual voltage Number of outputs Hysteresis Indicator light Trimmer adjustment
Compact Pressure Switch  Series ZSE2/ISE2
For vacuum 0 to –101 kPa
 Cross section: 0.31 mm2, Insulator O.D.: 1.55 mm Compliant with CE marking
01: R 1/8, M5 x 0.8 T1: NPTF 1/8, M5 x 0.8 0X: With suction filter (For mounting on ZX unit)
Connector DC polarity indicator Lever Hook
?Set the possible min. pressure for adsorption confirmation. If setting the pressure lower than that,
switch becomes ON in case that adsorption is not completely done. If setting the pressure higher than that,
(With no condensation and no freezing) Operating/Stored: 35 to 85%RH (With no condensation)
switch does not become ON even though it may absorb workpieces.
Set the ON-pressure by the pressure setting trimmer. Turning clockwise can set the high pressure/high vacuum pressure.
ISE2L For low pressure 0 to 100 kPa
Rated pressure range/Set pressure range Proof pressure Fluid Power supply voltage Current consumption Response time Repeatability
Temperature characteristics(Based on 25°C) Withstand voltage Insulation resistance
Lead wire   Grommet type     Connector type Standard
980 m/s2 in X, Y, Z directions, 3 times each (De-energized) ±3% F.S. or less 10 to 500 Hz at
0.2 to 0.33 mm2 Max. coating O.D. ?1.7 mm
The set pressure is the pressure selected to switch from OFF to ON condition.
1. Attaching and detaching connectors ?When assembling the connector to the switch housing,
push the connector straight onto the pins until the lever locks into the housing slot.
?When removing the connector from the switch housing, push the lever down to unlock it from the slot and then withdraw the connector straight off of the pin.
Lead wire 0.2 to 0.33 mm2 Max. coating O.D. ?1.7 mm
and then crimp with a crimping tool. When this is done, take care that the coverings of the lead wires
 do not enter the core wire crimping area. (Crimping tool: model no. DXT170-75-1)

火**售日本進口SMC小型壓力開關